Pack WALLBOX Pulsar Plus charging station - 5m Type 2 cable - 1.4 to 11kW - three-phase - Bluetooth - Wifi

A mini WALLBOX Pulsar Plus terminal, connected, and with adjustable power, designed for the home, indoors or outdoors

The WALLBOX Wallbox Plusar Plus single-phase charging station - three-phase - adjustable 1.4 to 11kW - Bluetooth - Wifi - Type2 5m cable is powered in three-phase. Its charging intensity can be adjusted instantly and at any time between 6A and 16A, via the Wallbox application. The charging station can therefore be configured to adapt to the power available in your home. Its attached T2 cable will ensure you secure recharging of your electric car in mode 3 .

Thanks to the Wallbox application , you can connect your charging station to your Smartphone by bluetooth or wifi. The application will allow you to manage the following parameters:

• Activate / Deactivate remote charging
• Set the charging power between 1.4 and 11kW
  
• Program the load at the desired time slots (to recharge only during off-peak hours for example)
• Configure the dynamic load, if the power boost is installed on the line
  

Attached cable 5m type 2

The charging station is already supplied with a charging cable attached to the charging station, type 2 and 5m long. This charging station is therefore compatible with all type 2 vehicles.

Wall cable tie included

The charging station is supplied with a wall cable tie that allows you to safely install the type 2 end cap after charging your vehicle.

Plug & Play activation

The charging station works in Plug & Play , as soon as you connect the cable to your vehicle and to the charging station, charging starts.

Recharge

From 7km (at 1.4kW) to 100km (at 11kW) more autonomy per hour of charging.

Mini size

The Wallbox Plusar Plus is one of the smallest charging stations on the market. Discreet, light, Design and practical. Size 16.6x16.3x8.2 cm. It is also robust (IK08) and resistant to heavy rains (IP55). It can be installed outdoors without rain protection.

Main features

• Activation: Plug & Play
• Adjustment of the charging intensity between 6 and 16A, adjustable via the app
• Bluetooth connection, Wifi: access to the Wallbox App and to the Wallbox web portal
• Three-phase power supply
• Terminal block for 10mm² rigid cable
• Leak detector direct current 6mA integrated in the terminal
• IP55 and IK08 protection: resistant to heavy rain and shocks
• Attached cable type2 length 5m
• Wall mounting kit included

Electrical protections

The following electrical protections are mandatory, and must be installed on a dedicated line. They have been validated by electricians and IRVE experts, and comply with the French regulations in force.

Protections to be installed if three-phase connection:

• Differential switch 40A - Type A Hi - 3P + N - 30mA - (ex: HAGER BDH440F ) - not included. A type A differential meets the standards since a leakage current detector is already integrated in the terminal.

• Circuit breaker 40A - 3P + N - Curve D - PdC 10kA (ex: HAGER NGT840 ) - not included

User interface

• IOs or Android app

Accessories

Three-phase installation

• Powerboost - Module of EM340 load management

Carplug test

The Carplug team has successfully tested the Wallbox Pulsar Pus terminal. The power supply connection is simple thanks to the 10mm² terminal block with its lever mechanism. No screwdriver needed to connect cables. The electrical protections selected by CARPLUG are compatible and ensure safe start-up.

The station turns on quickly, and is ready to charge in about 1 minute. We downloaded the Wallbox app, entered the serial number and Puk code, and the connection went smoothly. We then plugged in the cable: the charge started by itself at the intensity set on the application. If we change the intensity on the application, the charging intensity changes instantly on the car.

Review: Very positive. ideal terminal for a garage or a house, for a person wishing to monitor their consumption, manage their charging slots, and sometimes modify the charging intensity.